Measurements give you reliable data; interpreting that data and finding root causes is the job of vibration diagnostics. Our vibration analysts hold ISO 18436‑2 Category III certification.
Scope
What we offer
We choose measurement points and parameters to suit the machine type and the purpose of the measurement. Results are assessed against condition criteria and delivered in a clear report.
- Routine and periodic measurements
- Acceptance measurements on new machines
- Measurements after overhauls and upgrades
- Bearing and casing vibration measurements
- Trending results over time
- Report with condition assessment and recommendations
When to measure
When measurements make sense
Machine acceptance
Verifying the condition of a new or overhauled machine.
No online monitoring
Machines without a permanent vibration monitoring system.
Outage planning
Data to define the scope of an overhaul.
Worrying changes
Noise, rising temperature, vibration you can feel.
Periodic programme
Regular condition assessment of auxiliary machinery.
Warranty disputes
Independent measurement and documentation of machine condition.
Recognise one of these symptoms? An analyst will help find the cause.
Measurement scope
What we measure
Absolute vibration
Casing and bearing vibration velocity and acceleration.
Relative shaft vibration
Readings from eddy-current proximity probes, where installed.
Spectrum analysis
Frequency content as the basis for further diagnostics.
Assessment against criteria
Comparison with standards and the limit values for the machine.
Process
How we work together
- 01
Request
Machine type, purpose of the measurement, timing.
- 02
Measurement plan
Choice of measurement points and parameters.
- 03
On-site measurements
Measurements with portable instruments.
- 04
Evaluation
Analysis and assessment of the results.
- 05
Report
Results, condition assessment, recommendations.
Projects
Wind / renewables · 2017–2026
PGE wind farms: online monitoring and bearing diagnostics
PGE Energia Odnawialna, wind farms, Poland
- Vibration diagnostics
- Online condition monitoring
- Vibration measurements
Heavy industry & manufacturing · 2024
Recurring fan bearing failures at a cement plant
Cement plant, Poland
- Vibration diagnostics
- Laser shaft alignment
- Vibration measurements
Mining · 2024
Trim balancing of fans at a coal mine
Coal mine, Poland
- Machine balancing
- Vibration measurements
- Vibration diagnostics
Power generation · 2024
Start-up vibration measurements after a turbine overhaul
Power plant, Hungary
- Vibration measurements
- Vibration diagnostics
Related projects
2026
TAURON, Otmuchów hydropower plant · Poland
Independent vibration measurements on a hydro unit before its overhaul, as reference data for the overhaul.
2025
Bhotekoshi Power Company · Nepal
Vibration data of a 22.5 MW turbine-generator analysed: condition, recommendations and expected remaining service life.
2025
Volkswagen Poznań – Września plant · Poland
Vibration measurements on 28 electric motors with a diagnostic report and recommended repairs or operating changes.
2024
Power plant, Poland
Vibration measurements on a turbine-generator set with an ADRE data acquisition system.
2024
Bełchatów power plant (for the overhaul contractor) · Poland
Independent vibration measurements on turbine set no. 4 before its overhaul and at start-up afterwards.
2023
ANWIL, Włocławek · Poland
Measurements and an expert opinion on the current and expected condition of the gas turbine T-2101 rotor.
Related services
Typical machines
Other rotating machinery — e.g. wind turbines, gearboxes. Ask us →
Frequently asked questions
Didn't find your answer? Ask an engineer →
Which standards are used to assess vibration of industrial machinery?
We measure and assess vibration of rotating machinery in accordance with the relevant parts of ISO 20816, taking into account the type of machine, its design and its operating conditions. Depending on the machine, we apply ISO 20816-2 for steam turbines and generators, ISO 20816-3 for industrial machines, ISO 20816-4 for gas turbines and ISO 20816-5 for hydro units, among others. Acceptable vibration levels depend on the machine type, its technical parameters and the measurement location. That is why, in addition to assessment against the standard, we also analyse vibration spectra, trends, phase and the influence of operating conditions, which gives a more accurate picture of the machine's condition.
What is the difference between relative shaft vibration and absolute bearing vibration?
Relative shaft vibration describes the displacement of the shaft relative to a reference, usually the bearing housing, and is often measured with eddy-current probes. Absolute housing vibration is measured with seismic transducers, such as accelerometers. The two measurements provide different information about how a rotating machine behaves. The choice of measurement points and assessment criteria depends on the bearing design and the standard applied.
Which vibration parameters should be monitored on rotating machinery?
Depending on the machine's design, vibration displacement, velocity or acceleration is monitored, together with spectra, phase and trends. On machines with fluid-film bearings, relative shaft vibration and shaft position may be important. Assessing condition also requires context: rotational speed, load, temperature and process parameters. The scope of monitoring is defined for each specific machine.
When does high machine vibration require immediate action?
How urgent action is depends on the vibration level and how quickly it is changing, the type of machine and its criticality. Particular attention should be paid to a rapid increase in amplitude, new spectral components and simultaneous changes in temperature or bearing parameters. Alarm and trip values should be based on the manufacturer's documentation, the relevant standards and a risk assessment. A single universal limit should not be applied to all machines.
How should the ISO 20816 vibration evaluation zones be interpreted?
The relevant parts of the ISO 20816 series give vibration evaluation criteria for specific machine groups and measurement conditions. The evaluation zones help interpret the vibration level, but they are neither a universal indication of the cause of a fault nor an automatic trip setting. We relate the result to the machine type, measurement location, the manufacturer's recommendations and changes over time. It is also important to establish correctly which part of the standard applies.
What vibration levels are acceptable for industrial pumps?
The acceptable vibration level of a pump depends on its type, size, rotational speed, design and the measurement conditions. Assessment uses the manufacturer's requirements and the relevant standards for the pump category concerned, not one common value for the whole group. Besides amplitude, we assess the vibration spectrum, changes in process parameters and the condition of the pump and its driver. This helps distinguish mechanical from hydraulic symptoms.
What vibration levels are acceptable for electric motors?
Acceptable vibration of an electric motor is determined taking into account its size, speed, mounting and the measurement conditions. The reference points are the manufacturer's documentation and the relevant standards, such as the vibration evaluation requirements for the machine category concerned. In operation, trends and the character of the spectrum also matter, as they can indicate unbalance, misalignment or bearing faults.
How is steam turbine vibration assessed during run-up and coast-down?
During steam turbine run-up and coast-down, changes in vibration amplitude and phase are analysed as a function of rotational speed. This makes it possible to identify passages through critical speeds, changes in dynamic behaviour and some rotor instabilities. Measurements of relative shaft vibration and absolute bearing housing vibration are important, depending on how the turbine is instrumented. We compare the results with the machine's history and the manufacturer's requirements.
What is the difference between time-domain vibration analysis and FFT spectrum analysis?
The time waveform shows how the vibration signal changes over time, so it is useful for assessing impacts, instabilities and short-lived events. FFT analysis breaks the signal down into frequency components and makes it easier to relate them to rotational speed and to machine components. In vibration diagnostics the two methods complement each other. The choice depends on the symptoms and the purpose of the measurements.
What is shaft orbit analysis and what is it used for?
A shaft orbit shows the path of the shaft's movement in the measurement plane, based on the signals from two displacement probes. It is particularly useful in diagnosing rotating machinery with fluid-film bearings. The shape of the orbit and changes in it can indicate dynamic phenomena, but they need to be analysed together with the spectrum, phase, shaft position and operating conditions. An orbit alone does not determine the type of fault.
What is vibration phase analysis and when is it used?
Phase analysis determines the relative phase shift between vibration signals or their relationship to a once-per-turn reference. It helps identify vibration mode shapes and diagnose unbalance and misalignment, and it is used when balancing rotors. It is also important in run-up measurements, when the machine's dynamic response is assessed. Reliable interpretation requires correctly positioned sensors and a stable reference signal.
When are vibration measurements taken during machine run-up and coast-down?
Run-up and coast-down measurements are taken mainly when the problem depends on rotational speed or appears only in transient conditions. Amplitude and phase analysis helps identify resonances, critical speeds and changes in the stability of the rotor system. These tests are particularly useful for turbines and compressors and after major overhauls. The measurement procedure is agreed with the operators and the machine's start-up requirements.
What is the difference between vibration measurement and diagnostics?
Measurement provides data on the level and character of vibration. Diagnostics interprets that data, identifies the cause and recommends corrective action. If the results call for it, we can move straight on to diagnostics.
Which machines do you measure?
Pumps, fans, motors, compressors, turbines, generators, gearboxes and other rotating machinery.
Need a diagnosis or a quote?
Basic machine data and a short description are enough.