A correctly aligned drive train runs with lower vibration and less load on bearings and couplings, and with a lower risk of premature seal wear.
What's included
What we offer
Alignment covers an assessment of mounting conditions, checking and correcting the alignment, and a check measurement. Before-and-after results are documented in a report.
- Shaft and coupling alignment
- Soft foot check and correction
- Alignment of pumps, motors, fans and compressors
- Allowance for thermal growth, where data is available
- Check measurements after correction
- Report with before-and-after results
When to call us
Typical situations
Installation and replacement
A new machine, or a replaced motor or pump.
After an overhaul
Reassembly of the drive train.
2X component and axial vibration
Classic signs of misalignment.
Coupling wear
Coupling elements wearing out quickly.
Bearing and seal failures
Recurring damage.
Foundation changes
Settlement or modifications to the supporting structure.
Recognise one of these symptoms? An analyst will help find the cause.
Scope
How we align
Initial assessment
Measuring the as-found alignment and mounting conditions.
Soft foot
Checking for and eliminating soft foot.
Alignment correction
Shims and moves in the vertical and horizontal planes.
Final measurement
Confirming tolerances and reporting.
Process
How we work together
- 01
Request
Drive train type, speed, coupling.
- 02
Initial assessment
Measurement and soft foot check.
- 03
Correction
Bringing alignment within tolerance.
- 04
Check measurement
Verifying the result.
- 05
Report
Before-and-after results.
Projects
Related projects
2026
TAURON, Czchów hydropower plant · Poland
Coupling alignment checks on the flap gate drives during their modernisation.
2026
ORLEN Termika Silesia, Wodzisław Śląski · Poland
Diagnostics of 11 fans in Wodzisław and 4 at the Niewiadom branch, with balancing, alignment and acceptance.
2026
ORLEN Termika Silesia, Wodzisław Śląski (formerly PGNiG Termika EP) · Poland
Diagnostics of 11 fans with balancing, alignment and acceptance for operation.
2025
ORLEN Termika Silesia, Wodzisław Śląski · Poland
Diagnostics of 11 fans with balancing, alignment and acceptance for operation.
2024
2024
River weir, Poland
Shaft alignment of the weir gate drives; afterwards vibration dropped clearly and the motors drew less current.
Related services
Typical machines
Other rotating machinery — e.g. wind turbines, gearboxes. Ask us →
Frequently asked questions
Didn't find your answer? Ask an engineer →
What tolerances are used in laser shaft alignment?
In laser shaft alignment we first apply the tolerances specified by the manufacturer of the pump, motor, gearbox or coupling. Where none are specified, we select criteria based on the rotational speed and the operating conditions of the machine train. Where relevant, we also take into account the thermal growth of the machines between cold and operating conditions.
Does a pump need shaft alignment after an overhaul?
After a pump, motor or coupling has been dismantled and reassembled, it is worth checking the alignment of the drive train. Laser alignment reduces the additional loads on couplings, bearings and seals caused by incorrectly positioned shafts. The scope of measurement and correction is matched to the machine's design and the manufacturer's requirements.
What are the effects of poor pump and motor alignment?
Misalignment between a pump and its motor can increase the loads on the bearings, coupling and seals, and cause higher vibration and temperature. The effects depend on the type of coupling and the operating conditions of the train. Laser shaft alignment makes it possible to measure the relative position of the shafts and correct it to the agreed tolerances. The assessment should also take into account the condition of the foundations and possible thermal growth.
What are angular and parallel shaft misalignment?
Angular misalignment occurs when the shaft axes are not parallel to each other; parallel (offset) misalignment occurs when they are displaced from each other while running in roughly the same direction. In real machine trains both forms often occur together. During laser alignment of a pump, motor or gearbox, both are measured and the corrections to the machine's position are determined. The required tolerances depend on the design and operating conditions.
How is thermal growth compensated for during shaft alignment?
The position of the shaft axes can change between standstill and normal operating temperature. For this reason, cold alignment sometimes uses deliberate offsets that compensate for the expected thermal growth. The values should come from the manufacturer or from reliable measurements and calculations for the installation concerned. Ignoring these changes can lead to misalignment in operation, despite a good result measured at standstill.
How is alignment different from balancing?
Alignment corrects the relative position of shafts joined by a coupling; balancing corrects the rotor's mass distribution. Both reduce vibration, but they remove different causes.
Which machines do you align?
Pumps, motors, fans, compressors, gearboxes and other coupled drive trains.
Need a diagnosis or a quote?
Basic machine data and a short description are enough.